PMI Model DTA-2G18G-60-2 is a 10-Bit programmable 60dB PIN diode attenuator with a step resolution as low as 0.06dB over the frequency range of 2GHz to 18GHz. This model is offered in a slim line housing measuring only 0.5" in height.

# P7T-2G18G-60-T-1W

# PE2-40-100M18G-3R5-20-12-SFF

PMI Model No. PE2-40-100M18G-3R5-20-12-SFF is a 0.1 to 18.0 GHz, Low Noise Amplifier which provides a minimum of 37 dB of gain while maintaining a maximum gain flatness of +/-2.0 dB over the operating frequency. The noise figure is typically 3.5 dB from 2.0 to 18.0 GHz and 7.0 dB at 100 MHz and offers a minimum OP1dB of +20 dBm. The amplifier requires +14.5 to +28 VDC and has a nominal current draw of 525 mA. The unit is supplied with removable SMA (F) connectors in our standard PE2 housing.

# PS-360-DC-3 OPTION 618-15D

PMI Model No. PS-360-DC-3 OPTION 618-15D is an 8-bit, Digitally Controlled Phase

Shifter provides range of 360° in 256 Steps over the 6.0 to 18.0 GHz frequency

range. This unit has a typical insertion loss of 10 dB, accuracy of ±15° Max (Peak to

Peak) - Measured ±6.6°, PM/AM of ±2.5 dB Max - Measured ±1.2 dB and a VSWR of

2.0:1 Max It is supplied with removable SMA (F) connectors in a housing measuring

1.6" x 1.75" x 0.5".

# EWDM-2G6G-65-70MV

PMI Model No. EWDM-2G6G-65-70MV is a CW immune EW detector module

operating over the 2.0 to 6.0 GHz frequency range. This module features an

internal switch used to switch between the "Bit In" and RF In" with input blanking

on both ports. In addition, two amplified RF outputs are provided a 7 dB gain

channel and a 33 dB gain channel. The video output is designed to drive a 150 ft.

cable, while maintaining high speed, and excellent accuracy.

# PXS-500M18G-60-SFF

PMI Model No. PSX-500M18G-60-SFF is a pin diode transfer switch that operates over

the 500 MHz to 18 GHz frequency range. Specifications include 60 dB minimum

isolation, 3.0 dB maximum insertion loss, VSWR In/Out 1.9:1 maximum, +20 dBm CW

maximum input power and 100 ns maximum switching speed. This model incorporates

a TTL compatible driver for easy system integration. Hermetically sealed units are

available as an option. Features SMA (F) RF connectors, light weight design 1.4 oz and

package size of 1.0" x 1.0" x 0.5".

# PS-360-3237-8-292FF

PMI Model No. PS-360-3237-8-292FF is a High Speed, Millimeter Wave, 8-Bit Digitally

Controlled, Phase Shifter that operates over the frequency range of 32.0 to 37.0

GHz. This phase shifter offers a low insertion loss of 13dB typically and maintains a

VSWR of 1.8:1. The total phase shift range is 358.593° having a step size of 1.406° and

switches between states in less than 500ns. This model provides a high level of

accuracy by offering an amplitude error of ±1.5dB and a phase shift error of ±1.3°. Ultra-

Low DC Current consumption is offered at +15 VDC, 20 mA and -15 VDC, 10 mA. This

unit is supplied in a small housing measuring 1.15” x 1.80” x 0.4” with 2.92mm female

connectors.

# PE2-30-1R018R0-4R5-22-12-SFF-1

PMI Model No. PE2-30-1R018R0-4R5-22-12-SFF-1 is a 1.0 to 18.0 GHz, low noise

amplifier that typically provides 30 dB of gain while maintaining a maximum gain

flatness of ±1.5 dB over the operating frequency. The noise figure is 4.5 dB maximum

and offers an OP1dB of 22 dBm minimum The operating voltage is +12 to +15VDC with

a typical current draw of 500 mA. The unit is supplied with removable SMA(F)

connectors in our standard PE2 housing.

# SDLVA-0120-70-100M2G-10DBM

PMI model SDLVA-0120-70-100M2G-10DBM is a successive detection log video

amplifier (SDLVA) that operates between the 0.1 to 2.0 GHz frequency range. it has a

dynamic range of 70 dB minimum and a TSS of -65 dBm. This unit offers a maximum

rise time of 25 ns and a fall time of 30 ns. This model provides a limited IF output of

+10 dBm typically. The unit has SMA Female connectors in a gold plated housing

measuring 3.75 " x 1.50 " x 0.40".

# GMTA-1002

PMI model SDLVA-0120-70-100M2G-10DBM is a successive detection log video

amplifier (SDLVA) that operates between the 0.1 to 2.0 GHz frequency range. it has a

dynamic range of 70 dB minimum and a TSS of -65 dBm. This unit offers a maximum

rise time of 25 ns and a fall time of 30 ns. This model provides a limited IF output of

+10 dBm typically. The unit has SMA Female connectors in a gold plated housing

measuring 3.75 " x 1.50 " x 0.40".

# P4T-0R3G18G-70-T-SFF

PMI Model P4T-0R3G18G-70-T-SFF is a single pole four throw absorptive switch

operating from 0.3 GHz TO 18.0 GHz. It has a maximum insertion loss of 3.75 dB and

isolation of 70 dB minimum. Other specifications include VSWR 2.0:1, Maximum input

power +20 dBm CW maximum, Survival Power 1 W CW maximum (+30 dBm) and 10 W

Peak 1 μs Pulse, 1% Duty Cycle, Features SMA (f) RF connectors and a operating

temperature range of -40 ºC to +85 ºC.

# TD-30T-SHS-218-AMP-OPT4G4D5G-40DBM

PMI Model No. TD-30T-SHS-218-AMP-OPT4G4D5G-40DBM is an Ultra-High Speed,

High Sensitivity Threshold Detector optimized for the 4.0 to 4.5 GHz Frequency Range.

This unit has a fixed threshold level of -40 dBm. It is a miniature unit with TTL output

logic. Package size 2.5"(L) x 2.0"(W) x 0.5"(H) with SMA (F) connectors.

# SDLVA-218-60-70MV-CW

PMI Model No. SDLVA-218-60-70MV-CW is a CW immune SDLVA (Successive

Detection Log Video Amplifier). This unit operates from 2.0 to 18.0 GHz and has the

ability to interface with a long cable (65 FT), while maintaining high speed, flatness and

accuracy. Specifications include frequency flatness: ±2.0 dB Typ, Signal Capability:

Pulse (100 ns to 300 μs), Pulse on CW TSS: (-20 ºC to +85 ºC) -66 dBm for 10 MHz

Video Bandwidth, Log Dynamic Range -60 dBm to 0 dBm, Log Slope 70 mV/dB

nominal, Log Linearity ±1.5 dB Max,Max Input Level: +20 dBm CW, Video Output

Drive: Through 65 Feet, 75 Ohms Cable, Into 75 Ohms load, Power Supply +15 VDC

@ 400 mA Max, -15 VDC @ 150 mA Max and Operating Temperature -20 °C to +85

°C. Package size 2.3" x 2.2" x 0.4" with SMA female connectors and conduction cooling

at mounting surface.

# DLVA-8G10G75-50-SFF

PMI Model No. DLVA-8G10G75-50-SFF is a 8.0 to 10.0 GHz, Detector Log Video

Amplifier. This unit has a dynamic range of -75 dBm to 0 dBm, a log linearity of ±1.8 dB,

and a log slope of 50 ± 4 mV/dB. Other specifications include Frequency Flatness of

±1.2 dB, TSS of -78 dBm, Log Linearity ±1.8 dB - Measured ±1.3 dB, Log Slope 50 ± 4

mV/dB, and Output DC Offset 50 ± 50 mV. Power Supply: +15 V @ 350 mA, -15 V @

100 mA and SMA (F) connectors. Unit size is 2.0" x 1.5" x 0.4" with Electroless Nickel

Plate finish.

# PE2-500M18G-5R0-21-12-SFF

PMI Model No. PE2-500M18G-5R0-21-12-SFF is a 0.5 to 18.0 GHz, low noise amplifier

that provides 24 dB min of gain while maintaining a maximum gain flatness of ±2.0 dB

over the operating frequency. The noise figure is 5.0 dB maximum and offers a typical

OP1dB of 21 dBm. The operating voltage is +12 to +15 VDC with a nominal current

draw of 375 mA. Supplied with removable SMA(F) connectors in our standard PE2

housing.

# PLNA-35-100M18G-P1dB24-120VAC

PMI Model No. PLNA-35-100M18G-P1dB24-120VAC is a portable amplifier that

operates over the 100 MHz to 18.0 GHz frequency range. This model provides 40

dB typical gain with a minimum OP1dB of +24 dBm, Gain Flatness: ±2.0 dB

Typical, VSWR In/Out: 2.0:1 Typical, Noise Figure: 3 dB. This amplifier features an

illuminated push button On/Off switch in a small package (3.0" x 3.0" x 1.75") with

Type N connectors. Gold plated finish.

# PDT-8G12G-40-515-SFF

PMI Model No. PDT-8G12G-40-515-SFF is an 8.0 to 12.0 GHz, 2 way high power

switch that has an insertion loss of 2.0 dB maximum and a VSWR of 1.8:1

maximum. The operating power is +40 dBm CW average, +57 dBm 1 μs, 1% duty cycle

with an isolation of 40 dB minimum. Switching Speed 200 ns maximum - measured 100

ns, power supply requirements +5 V @ 100 mA and -15 V @ 60 mA. Features include

SMA female connectors. Unit size is 1.15" x 1.25" x 0.30" with painted blue finish.

# EWDM-2G6G-65-70MV

PMI Model No. LM-10M2D5G-100CW-1KWP-SFF is a RF limiter that operates in the 10

MHz to 2.5 GHz frequency range. This limiter can handle 100 W CW and 1 KW peak

(1% duty cycle, 1 μs maximum pulse width) input power and provides a maximum

leakage of +13 dBm CW input. This module has a low insertion loss of 0.5 dB and a

recovery time of 2 μs typical. Package size is 1.86” x 0.65” x 0.38” with SMA

Female connectors

# LNA-35-500M2D5G-0D6-25-12-SFF

PMI Model No: LNA-35-500M2D5G-0D6-25-12-SFF is a Low Noise Amplifier operating

over the 0.5 to 2.5 GHz, Low Noise Amplifier. This model offers a typical gain of 35 dB

while maintaining a typical gain flatness of ±1.6 dB and a maximum noise figure of 0.6

dB. This compact model is outfitted with SMA female connectors in housing measuring

1.25" x 1.25" x 0.563".

# DTA-14G40G-32-CD-2

PMI Model No. DTA-14G40G-32-CD-2 is a 10 Bit programmable attenuator with

step resolution as low as 0.04 dB which provides over 32 dB of attenuation over

the frequency range of 14.0 to 40.0 GHz. This model is offered in a slim line

housing measuring 2.0" x 1.8" x 0.5" with 2.92mm female connectors and

operates on a single +15 VDC supply with only 40 mA of current consumption

typically. Specifications include Insertion Loss 9.0 dB Typical, VSWR 2.0:1,

Attenuation Flatness ±1.5 dB Typical, Attenuation Accuracy ±2.0 dB Typical,

Power handling of +24 dBm CW maximum, and Input 1dB Compression: +10 dBm

Typical.